{"product_id":"uninterruptible-power-supply-ups-hat-b-for-raspberry-pi","title":"Uninterruptible Power Supply UPS HAT (B) for Raspberry Pi","description":"\u003cp\u003ePower your Raspberry Pi seamlessly with this Uninterruptable Power Supply HAT (B) from Waveshare! This UPS HAT is designed to ensure your Raspberry Pi has a constant power source in the event of a power cut or when moving between sockets.\u003c\/p\u003e\n\u003cp\u003eThe HAT holds 2x 18650 batteries (\u003cstrong\u003ebatteries\u003c\/strong\u003e \u003cstrong\u003enot included\u003c\/strong\u003e but available to buy here) which take over from the included 8.4V power supply whenever it's disconnected or power is cut. When the power supply is connected, the HAT will charge the batteries with comprehensive onboard battery protection. The HAT can provide up to 5A (peak) to your Raspberry Pi via the onboard regulator, allowing lots of headroom for busy projects.\u003c\/p\u003e\n\u003cp\u003eBattery warning indicators safeguard against incorrect battery installation, and you can also check the status of your batteries in real-time via I2C, monitoring voltage, current, power and remaining capacity:\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0176\/3274\/files\/UPS-HAT-B-for-Raspberry-Pi-4-10_1.jpg?v=1642623558\u0026amp;width=700\" alt=\"UPS I2C Monitoring\"\u003e\u003c\/p\u003e\n\u003cp\u003eThere's even a 5V USB-A port for powering other devices! The HAT comes complete with a \u003cstrong\u003eUK\u003c\/strong\u003e power supply, acrylic protection panel and fixings.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePlease turn the power switch to OFF before you connect batteries!\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eDesigned for the Raspberry Pi\u003c\/li\u003e\n\u003cli\u003eCompatible with Raspberry Pi 4, 3B+\/3\u003c\/li\u003e\n\u003cli\u003eAccepts 2x 18650 batteries (not included)\u003c\/li\u003e\n\u003cli\u003eMounts below the Raspberry Pi, leaving your GPIO pins available for HATs and hardware\u003c\/li\u003e\n\u003cli\u003ePogo pin connection to the Raspberry Pi - no GPIO pins consumed\u003c\/li\u003e\n\u003cli\u003eReal-time I2C bus communication, monitoring the battery voltage, current, power, and remaining capacity\u003c\/li\u003e\n\u003cli\u003eMulti battery protection circuits: overcharge\/discharge protection, over current protection, short circuit protection, and reverse protection, along with the equalizing charge feature\u003c\/li\u003e\n\u003cli\u003eOnboard 5V regulator, up to 5A continuous output current, more sufficient power source for your Raspberry Pi projects\u003c\/li\u003e\n\u003cli\u003e5V USB output, convenient for powering other boards and accessories\u003c\/li\u003e\n\u003cli\u003eBattery warning indicators, easy to check if the battery is connected correctly\u003c\/li\u003e\n\u003cli\u003eOnline development resources and manual\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eRequires\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e2x 18650 batteries\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eOutput voltage: 5V\u003c\/li\u003e\n\u003cli\u003eCharger: 8.4V 2A\u003c\/li\u003e\n\u003cli\u003eControl bus: I2C\u003c\/li\u003e\n\u003cli\u003eBattery supported: 2x 18650 Li batteries (NOT included)\u003c\/li\u003e\n\u003cli\u003eDimensions: 56 × 85mm\u003c\/li\u003e\n\u003cli\u003eMounting holes: 3.0mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003ePackage Contents\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e1x UPS HAT (B)\u003c\/li\u003e\n\u003cli\u003e1x UK 8.4V battery charger\u003c\/li\u003e\n\u003cli\u003e1x Acrylic protection panel\u003c\/li\u003e\n\u003cli\u003e1x Screws pack\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRaspberry Pi and batteries not included\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch2\u003eResources\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eProduct Wiki\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUsage tips\u003c\/strong\u003e\n\u003cul\u003e\n\u003cli\u003ePlease turn the power switch to OFF before connecting batteries, or the board may be damaged due to shorting\u003c\/li\u003e\n\u003cli\u003eAfter installing batteries, make sure that the Pogo pins are completely aligned with the pin header before turning on the power. If the Pogo pins are not conducting, you can press the pin to loosen it or use a knife to scratch off any oxide layer on the pin header\u003c\/li\u003e\n\u003cli\u003eThe board may not work when you mount the batteries for the first time, you need to press the Boot button to activate the circuit\u003c\/li\u003e\n\u003cli\u003eWhen connecting the battery for the first time, you need to pay attention to whether the warning LED is on. If the LED is on, it means that the corresponding battery is connected the wrong way round.\u003c\/li\u003e\n\u003cli\u003eIt is recommended not to exceed 4A when working for long periods or when working with high current loads. It will heat up when working at 5A for long durations. Pay attention to heat dissipation.\u003c\/li\u003e\n\u003cli\u003eUse the included power supply only! Using other power sources may cause damage due to large\/unstable output power ripples\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Waveshare","offers":[{"title":"Default Title","offer_id":48624289284314,"sku":"xvp1789688916519","price":22.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0824\/8318\/3834\/files\/uninterruptible-power-supply-ups-hat-b-for-raspberry-pi_1.jpg?v=1789688921","url":"https:\/\/memoryfoamwear.shop\/products\/uninterruptible-power-supply-ups-hat-b-for-raspberry-pi","provider":"My Store","version":"1.0","type":"link"}